350℃ High‑temperature Resistant HTV Silicone Rubber: Grade Selection, Thermal‑aging Performance, Processing & Storage Guidelines

Hits: 1641 img

1. Product Overview

350‑degree‑grade high‑temperature‑resistant HTV high‑temperature mixing silicone rubber supports two mainstream processing technologies: compression molding and extrusion. The compound presents pale‑yellow appearance and covers four hardness grades from 40 Shore A to 70 Shore A, balancing thermal stability and mechanical properties. It targets the manufacturing of sealing and pipeline components working under high‑temperature conditions. For food‑contact articles, finished parts made from this rubber must undergo post‑curing at 200 °C for 4 hours to meet prerequisites for contact service.

2. Typical Key Performance Range

Test data are obtained on 2‑mm‑thick specimens, cured under pressure at 175 °C for 5 min with 0.6 % 95 % DBPMH peroxide curing agent:

  1. Hardness grades: 40A, 50A, 60A, 70A; density 1.14‑1.20 g/cm³.
  2. Virgin mechanical properties: tensile strength 8.5‑9.5 MPa; elongation‑at‑break 400‑700 %; tear strength 15‑25 MPa.
  3. Properties after thermal aging at 300 °C for 72 hours: Hardness increases after aging; tensile strength remains 4.9‑5.2 MPa, and residual elongation ranges 160‑350 %. The material retains rubber elasticity for long‑term high‑temperature service.

Note: The above data are for standard test specimens. Custom‑formulated products shall not adopt these values. Technical communication shall be performed to define performance boundaries before custom development.

3. Main Application Fields

  1. Heat‑resistant sealing parts: static and dynamic sealing components for high‑temperature equipment.
  2. Heat‑resistant extruded tubing: silicone extruded tubes for high‑temperature fluid transportation.

4. Critical Notes for Processing & Post‑curing

  1. Curing system: compatible with DBPMH (2,5‑dimethyl‑2,5‑di(tert‑butylperoxy)hexane) peroxide; reference compression‑molding condition:175 °C /5 min.
  2. Mandatory requirement for food‑contact applications: post‑curing at 200 °C for 4 hours after molding to eliminate low‑molecular volatiles.
  3. Risks of omitted post‑curing: Articles without post‑curing are prone to volatile precipitation and performance degradation under high‑temperature exposure and shall not be used for contact‑type service conditions.

5. Packaging, Storage & Shelf‑life FAQ

  1. Packaging: 20 kg per carton.
  2. Storage: Keep in cool, dry and shaded environment. Unopened material stored at room temperature has a 1‑year shelf‑life counted from production date. It is industry‑recommended to consume within 3 months.
  3. Storage exceeding 3 months: Plasticity of rubber compound will shift; mixing duration should be appropriately extended during compounding.
  4. Expired‑material judgment: Expiration does not mean direct discard. Before production, core properties including hardness, tensile strength and elongation must be retested to verify fitness for service conditions.

6. Common Pitfalls in Material Selection

  1. Do not rely merely on nominal maximum temperature rating. Always check residual elongation and tensile strength after thermal aging. Some rubbers show good room‑temperature indicators but lose elasticity rapidly upon high‑temperature exposure.
  2. Higher hardness brings improved virgin tear resistance yet significantly reduces elongation‑at‑break. The 70A grade delivers only 400 % initial elongation, dropping to 160 % after 72 h aging at 300 °C. For dynamically reciprocating seals, lower‑hardness grades should be preferentially evaluated.
  3. Custom‑formulated grades differ from standard products; standard data sheets cannot be directly applied.
  4. Post‑curing procedure cannot be skipped for food‑contact applications.

7. Industry Summary

For industrial high‑temperature sealing and extruded high‑temperature tubing, 350‑℃‑grade HTV high‑temperature‑resistant silicone rubber addresses rapid elasticity failure of ordinary silicone rubber under prolonged high‑temperature exposure. Material selection should not be based solely on room‑temperature parameters. Mechanical retention after 300‑℃‑level thermal aging acts as the core selection criterion. Meanwhile, vulcanization process, post‑curing treatment and storage‑cycle control directly determine real‑world service life of finished components under high‑temperature operating conditions.


High Temperature Resistance Silicone Rubber(350℃) ,pls check IOTA HTV 329

Online QQ Service, Click here

QQ Service

What's App